12/6/2023 0 Comments Jumbo toilet wax ringThe use of a ring with a horn can mean you've pushed all of the wax out and have just the plastic horn to make the seal (it won't!).This is probably the most common path taken by DIYers. This often doesn't look 's much better to have the toilet sitting flush on the floor and only use shims if it rocks without the wax in place (generally, either the floor or the toilet are not perfectly flat, which requires the shims to keep it from rocking and provide a small layer of continuous wax to make the seal). Since there needs to be at least a thin layer of wax all around, if you choose not to change the flange and install it properly, then you'll need to shim such that the toilet sits above the flange and DOES NOT ROCK! THEN, you can reset it with the wax. So, you only get one chance to press the toilet down, and placing shims AFTER you've set the toilet can easily cause it to be in a different position and the wax have a gap in it.Īs has been said, if the toilet does not sit flat on the floor before you've added the wax, you have a problem. Wax is not a spring.once you compress it, it does not spring back. It would look better because the toilet would not be elevated and it would be stronger. ![]() Now doing it right by getting a new flange with a stainless steel ring in place would be best. Somebody may post a better suggested procedure. This procedure is not tested by experience. Polyseamseal is also available in white, which may be a better choice with your toilet sitting up some. Your shims and gaps will be a bit visible through the Polyseamseal. Note that while Polyseamseal tub and tile caulk goes on white, the common "clear" type turns semi-clear. Once the caulk is in place to your satisfaction, immediately and carefully remove the masking tape. ![]() You could use a nitrile glove over your finger if you prefer to not use your bare finger. You can use a wet finger to push in and smooth and taper to the tape. (a practiced person would not need the masking tape, but that is not us.) Apply Polyseamseal tub and tile caulk to the front 85% of the toilet bottom. So how tight should you make the nuts? If I looked it up and gave you a torque, would that help? If not, maybe use 1 finger on a 6 inch wrench? But I don't know how strong your finger is.Īpply masking tape to the floor and toilet to limit where the cauking will stay. Tighten the nuts again if they are a bit loose. Now cut off or snap off the shims that are sticking out. If a shim is loose and you cannot push it in more, pull it out, cut maybe 1/2 inch off of the thin end, and push it back in. Once down, be sure that the shims are each tight. Mark where the shims are with masking tape or washable marker. Position the shims to make the toilet level (use a level) and a little higher than where it sat limited by the flange. With the wax cleaned off, set the toilet in place. If you want to have a toilet that works without leaking for least cost, put some 3/8 or more shims in the front. I am going to assume that you don't measure things with more than 1/8 resolution. This would probably increase your chance of getting guesses on pricing. ![]() I suggest posting a photo or 2 that shows the elevation and the materials involved. Some plumber caulk all the way around, depending on their local code. This will further hold the toilet and help keep spilled water from getting under the toilet. The final step is to caulk around the base of the toilet, leaving the back side open. The flange bolts are not intended to force the toilet into the wax, they are just to hold the toilet from tipping or shifting. Now you use you body weight to press the toilet's horn firmly into the wax.as far as it will go. The flange bolts you secured earlier will guide the toilet so it will set down squarely on the wax. In situations where the flange is below the floor and 2 rings are needed, the funnel ring goes on top. Now, put the flange bolts in place and use extra nuts to secure them in place. This will show what shimming is necessary and where they will go. Then you should set the toilet on the flange without wax. It should rest on the finished floor and be anchored though into the sub floor. First, the flange is not installed correctly.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |